Modeling and Simulation of Artificial Core-Shell Based Nanodielectrics for Electrostatic Capacitors Applications
D. Musuwathi Ekanath, N. Badi, and A. Bensaoula
Center for Advanced Materials, University of Houston, Houston, TX
Dept. of Physics, University of Houston, Houston, TX
The need for high storage capacitors led to the development of polymer based capacitors. Polymers have high processability, mechanical flexibility, electrical breakdown strength and compatibility with printed circuit board (PCB) technologies; but usually have very low permittivity (K). In COMSOL Multiphysics software, the AC/DC module is selected and the In-plane electric currents are applied ...
The Transient Modeling of Single-Bubble Nucleate Boiling in a Sub-Cooled Liquid Using an ALE Moving Mesh
C. J. Forster, and M. K. Smith
Georgia Institute of Technology
This paper investigates the evolution of a single bubble going through growth, pinch-off, and condensation while rising due to buoyancy forces in a sub-cooled liquid. Phase change is modeled on the evolving liquid-vapor interface by considering changes in enthalpy and heat fluxes at the interface. A comparison of the ALE model is made with the same single-bubble system computed with a level-set ...
E. Evgin, J. Infante Sedano, and Z. Fu
University of Ottawa
This paper is a part of a study on energy piles for heating and cooling of buildings. Energy piles are used for two reasons: (1) to transfer structural loads to foundation soils, and (2) to transfer heat from foundation soils to the building for space heating in winter time and for cooling purposes in summer time by transferring heat from the building to the foundation soils. The efficiency of ...
T. Ekwevugbe, and G. Bevan
Institute of Energy and Sustainable Development, De Montfort University, Leicester, United Kingdom
School of Engineering and Computing, Glasgow Caledonian University, Glasgow, Scotland
An investigation was undertaken into the suitability of using COMSOL for modeling an aircraft capacitive fuel gauging unit. A model of a sensor immersed in a fluid was developed for rectangular tank geometry with a range of fluid levels and sensor orientation using the electrostatics application mode in COMSOL’s AC/DC module The importance of modeling the capacitance of air was demonstrated. ...
Calculating and Observing Opto-Mechanically Induced Surface Acoustic Waves in a Silica Whispering Gallery Microresonator
Photonics Research Center
United States Military Academy
West Point, NY
Here we calculate opto-mechanically induced Surface Acoustic Waves upon a silica microresonator using COMSOL. Using conservation of momentum, we show both analytically and numerically that the photonphonon interaction within the resonator cavity causes a moving train of electrodes - a virtual grating of matter density – that displace material in different directions and magnitudes. This ...
Laminar Fluid Flow and Heat Transfer Studies of an Electrical Conducting Fluid Subject to Combined Electric and Magnetic Fields
E. Gutierrez-Miravete, T. DePuy, and X. Xie
Rensselaer at Hartford, Hartford, CT
Pratt & Whitney, East Hartford, CT
The flow of electrically conducting fluids such as liquid metals is significantly affected by applied electric and magnetic fields. The effect has important industrial applications in metallurgy, nuclear technology and other fields. This paper described results of a series of studies designed to investigate the capabilities of COMSOL Multiphysics to accurately simulate the steady laminar flow ...
P. Lin, C. Chang, H. Huang, and B. Zheng
Mechanical and Aerospace Eng., Rutgers, The State University of New Jersey, Piscataway, NJ
FTR Systems (Shanghai) Inc., Shanghai, China
PolarOnyx, Inc., San Jose, CA
School of Mechatronics Eng., University of Electronic Science and Technology of China, Chengdu, China
The heat sink designs using impinging liquid jets, which form stagnation flows, feature uniform heat transfer coefficients, and provide thin thermal boundary layers, are studied to reduce the heat from GPUs. Three different designs using central, micro, and uniform-cross-section (UCS) central jets are studied and simulated in COMSOL. The efficiency factors, defined as the ratio of total ...
A. Roday, and P. Nicosia
Garlock Sealing Technologies
Sintering is an important step in the manufacturing of polytetrafluoroethylene (PTFE) billets. The challenge in heating large billets stems from the inherent low thermal conductivity of PTFE. Existing literature suggests determining maximum heating rate experimentally using recommended guidelines. This paper uses COMSOL to aid in optimizing the temperature profile required for a particular ...
N. Bhalla, S. Li, and D. Chung
Chung Yuan Christian University, Taiwan, (R.O.C)
National Tsing Hua University, Taiwan, (R.O.C)
Different configurations of MEMS based accelerometer has been made and analysed using COMSOL Multiphysics. The designs presented in this paper consist of a square shaped proof mass with flexures supporting it. Different position and varied number of supporting flexures attached to the proof mass makes each configuration distinct. The piezoresistors are placed near the proof mass and frame ends on ...
A. Sun, and S. Murray
Dept. of Biomedical Engineering
UCLA, Los Angeles, CA
Implantable Collagen sponges are used in Spinal Surgery as Drug Delivery Scaffolds. An optimal concentration of growth factor that strikes a balance between bone growth and adverse diffusion effects is difficult to find. The porous sponge also serves as a scaffold for Osteoblast growth, and fluid shear has been shown to mediate biological effects on that cell type. We use COMSOL Multiphysics ...