K. O. Lund , S. M. Lord ,
 Kurt Lund Consulting (COMSOL Certified Consultant), Del Mar, CA, USA
 SML Associates, Encinitas, CA, USA
A frequently occurring geometry for heat exchangers is that of a long tube wound into a helix or spiral around a core volume. There is to be heat exchange between the tube and the gases (or solids) in the core. However, the length scales of these two parts of the geometry are very different, thus complicating the interface between the tube and the core processes. Usually, the tube is too ...
S. Yushanov, J. S. Crompton, K. C. Koppenhoefer
AltaSim Technologies, LLC., Columbus, OH, USA
This study analyzed the laser powder bed additive manufacturing process. The laser is modeled as a moving heat source with time dependent heat transfer causing local, transient melting of the metal powder. Heat transfer is considered to take place due to convection in the molten metal pool, solidification of molten metal and conduction, convection and radiation to the surrounding environment. ...
P. L. Mills , K. Barman , S. Mothupally , A. Sonejee ,
 Texas A&M University - Kingsville, Kingsville, TX, USA
Introduction Fluid flow patterns in research or process-scale equipment where a fluid is contained between concentric rotating cylinders in the absence of bulk axial flow has received notable attention in the field of fluid mechanics. Annular flows occur in many practical applications, such as in the production of oil and gas, fluid viscometers, centrifugally-driven separation processes, ...
Mitsubishi Turbocharger & Engine Europe, Almere, The Netherlands
This study presents a rotordynamic analysis of a rotor on hydrodynamic bearings using COMSOL Multiphysics®. In this paper, the complexity of the model is gradually increased. Starting point of the analysis is the modal analysis of the rotor in free-free conditions. A Reynolds model is set up to predict the film pressure distribution under shaft loading. Due to the cross coupling terms of the ...
Computation of Velocity, Pressure and Temperature Distributions near a Stagnation Point in Planar Laminar Viscous Incompressible Flow
E. Kaufman, and E. Gutierrez-Miravete
Pratt and Whitney, East Hartford, CT, USA
Rensselaer at Hartford, Hartford, CT, USA
As gas turbine temperatures and component life requirements continue to rise, it becomes increasingly important to have a good understanding of the operating temperatures of their components. The objective of this study was to explorate whether a Hiemenz flow approximation based on measured static pressures near an airfoil leading edge can provide a good estimate of the leading edge heat ...
B. Hari, S. Bakalis, P. Fryer
The University of Birmingham, School of Chemical Engineering, Edgbaston, Birmingham, United Kingdom
Worldwide attention in the computational modeling and simulation of the human intestine is increasing in order to help understand its complex behavior and improve health. Computational fluid dynamics is an essential tool to understand the mechanics and transport phenomena of the human intestine, thereby advancing the diagnosis and treatment of gastrointestinal related diseases. The aim of this ...
S. Gorelick, M. Leivo, U. Kantojärvi
VTT Technical Research Centre of Finland, Espoo, Finland
Excessive air damping can be detrimental to the performance of oscillating MEMS components. Complex systems, such as structures in pre-etched cavities or angular comb-drive scanning mirrors, typically require simulations to reliably evaluate the air damping. The simulated and experimental performance of the following systems was evaluated and compared: two types of out-of-plane cantilevers, in ...
P. S. Fodor, M. Kaufman
Cleveland State University, Cleveland, OH, USA
In this work we investigate computationally the use of spiral channels at Reynolds numbers from 25 to 900 as a mixing structure (Figure 1) using COMSOL Multiphysics, the CFD Module, and the Chemical Species Transport physics. In this system, the centrifugal forces experienced by the fluid as it travels along the curved trajectory induce counter-rotating flows. The presence of these transversal ...
E. Holzbecher, and Hang Si
Weierstrass Institute for Applied Analysis and Stochastics (WIAS), Berlin, Germany
In the paper we examine the accuracy of various meshes for different model regions and simple differential equations in 2D and in 3D. We study the potential equation for a single irregular domain (2D testcase 1), for a simple domain with irregular sub-domains (2D testcase 2) and a 3D testcase. For testcase 1 we compare with the analytical solution, for testcases 2 with the best solution, ...
A. Métais , S. Matteï , I. Tomashchuk , S. Gaied 
 ArcelorMittal, Montataire, France
 Laboratoire Interdisciplinaire Carnot de Bourgogne, Université Bourgogne Franche Comté, France
Laser Welded Blank solutions enable to reduce vehicles weight and to optimize their crash performances by means of simultaneous tuning of different grades and thicknesses. The present work aims to characterize numerically and experimentally materials mixing during laser welding. For better understanding of materials mixing based on convection-diffusion process in case of full penetrated laser ...